Din Rail Power Supplies
Showing 196–210 of 219 results
-
96.6W 13.8V 4.5A 13.8V 2.5A UPS Function DIN Rail Power Supply
96.6W 13.8V 4.5A 13.8V 2.5A UPS Function DIN Rail Power Supply
-
96.6W 27.6V 2.25A 27.6V 1.25A UPS Function DIN Rail Power Supply
96.6W 27.6V 2.25A 27.6V 1.25A UPS Function DIN Rail Power Supply
-
960W 24V 40A Three Phase DIN Rail PSU
DRT-960 series are three-phase models that are powered by 340~550VAC 3-phase ~ 4 wire power system. Featuring up to 92% of high efficiency, this series can be cooled by free air convection which significantly increases the reliability and lifetime of the power supply. A built-in constant current limiting circuit means DRT-960 possesses the ability to…
-
960W 48V 20A Three Phase DIN Rail PSU
DRT-960 series are three-phase models that are powered by 340~550VAC 3-phase ~ 4 wire power system. Featuring up to 92% of high efficiency, this series can be cooled by free air convection which significantly increases the reliability and lifetime of the power supply. A built-in constant current limiting circuit means DRT-960 possesses the ability to…
-
960W Three Phase AC-DC Industrial DIN Rail PSU
960W Three Phase AC-DC Industrial DIN Rail PSU
Features
- Three-Phase AC 340 ~ 550V wide range input
- High efficiency 91% and low dissipation
- Short circuit/Over load/Over voltage/Over temperature protection
- Optional parallel function(1+1)
- Cooling by free air convection
- Can be installed on DIN rail TS-35/7.5 or 15
- UL 508(industrial control equipment)approved
- EN61000-6-2(EN50082-2) industrial immunity level
- 100% full load burn-in test
-
960W Three Phase DIN RAIL with PFC Function
960W Three Phase DIN RAIL with PFC Function
Features
- Three-phase AC 340-550V wide range input (Dual phase operation possible)
- Width only 110mm
- Built-in active PFC function compliance to EN61000-3-2
- High efficiency 94.5% and low power dissipation
- Protections: Short circuit/Overload/Over voltage/Over temperature
- Cooling by free air convection
- Built-in constant current limiting circuit
- Can be installed on DIN rail TS-35/7.5 or 15
- UL508 (Industrial control equipment) approved
- EN61000-6-2 (EN50082-2) industrial immunity level
- Current sharing up to 3840W (3+1)
- Built-in DC OK relay contact
- 100% full load burn-in test
-
960W Ultra Slim DIN Rail Power Supply
960W Ultra Slim DIN Rail Power Supply
Features
- AC Input 180~264VAC
- 130% peak load capacity
- Width only 110mm
- Built-in active PFC function compliance to EN61000-3-2
- High efficiency 94% and low power dissipation
- Protections: Short circuit/Overload/Over voltage/Over temperature
- Cooling by free air convection
- Built-in constant current limiting circuit
- Can be installed on DIN rail TS-35-7.5 or 15
- UL508 (Industrial control equipment) approved
- EN61000-6-2 (EN50082-2) industrial immunity level
- Current sharing up to 3840W (3+1)
- Built in DC OK relay contact
- 100% full load burn-in test
-
96W 24V 4A Miniture Din Rail Power Supply
96W 24V 4A Miniture Din Rail Power Supply
-
96W 48V 2A Miniture Din Rail Power Supply
96W 48V 2A Miniture Din Rail Power Supply
-
97.5W 15V 6.5A 100W Class II DIN Rail Power Supply
DR-100 Series is a Class II switching power supply. Designed with a fully isolated plastic case to prevent user contact and the risk of shock. Other standard features include its low no load power consumption, to save energy, short circuit, over load, over voltage and over temperature protections.
-
99.6W 12V 8.3A DIN Rail Type Converter
DDR-120A-12 is a 99.6W 12V 8.3A DIN Rail Type Converter.
Features
- Compliance to EN50155 and EN45545-2 railway standard
- Width only 32mm
- 2:1 wide input range
- -40~+70°C wide working temperature
- 150% peak load capability
- DC output adjustable
- Cooling by free air convection
- Can be installed on DIN rail TS-35/7.5 or 15
- Protections: Short circuit / Overload / Over voltage /Input reverse polarity / Input under voltage protection
- 4KVdc I/O isolation(Reinforced isolation)
- 3 years warranty
-
Din Rail Instal Redundant Module
20A redundancy (decoupling) module for 24Vdc power system. Containing 2 sets of 20A Or-ing diodes with wonderful heat dissipation deployment, DR-RDN20 gives you a new option for safe connection of 1+1 redundant set-up. Not only perfectly decoupling power sources from each other but also from the load, DR-RDN-20 also provides users monitoring signals for both…
Features
- Suitable for redundant operation of 24V system
- Installed on DIN Rail TS35 / 7.5 or 15
- Relay contact signal output and LED indicator for input failure alarm
- Cooling by free air convection
-
DR-4505 5V 5A Din Rail Power Supply
DR-45- are din rail mountable switched mode power supplies designed for rack mount applications in 5V, 12V, 15V & 24V outputs. Featuring a fixed switching frequency at 100KHz and suitable for installation on TS35/7.5 or 15 they are a versatile range of units. Standard features include Short circuit, over load, over voltage and over temperature…
-
DR-4512 12V 3.5A Din Rail Power Supply
DR-45- are din rail mountable switched mode power supplies designed for rack mount applications in 5V, 12V, 15V & 24V outputs. Featuring a fixed switching frequency at 100KHz and suitable for installation on TS35/7.5 or 15 they are a versatile range of units. Standard features include Short circuit, over load, over voltage and over temperature…
-
DR-4515 15V 2.8A Din Rail Power Supply
DR-45- are din rail mountable switched mode power supplies designed for rack mount applications in 5V, 12V, 15V & 24V outputs. Featuring a fixed switching frequency at 100KHz and suitable for installation on TS35/7.5 or 15 they are a versatile range of units. Standard features include Short circuit, over load, over voltage and over temperature…
Sunpower’s DIN rail power supplies range is available in an array of different form factors and power ratings, starting at 10W going up to 960W with output voltages from 5 to 48 volts. All of our DIN rail power supplies are of a fan less design but each individual product has their unique functions and input characteristics, whether it be a wide or high input range, or one, two or three phase operation.
All of our products are installed on DIN rail TS35/7.5 or 15 and the majority of our DIN rail power supply units come with built-in PFC. Other features within our DIN rail power supply units include low no load power consumption, DC OK relay contact and high efficiency. A number of the larger DIN rail power supply units that we stock also have a parallel function so that current sharing can be achieved which allows for installs to be created of up to 3840W with redundancy and UPS modules also available.
Our DIN rail power supplies are designed for use in industrial, automation and process control applications and meet the requirements of UL508, for industrial control equipment and will provide the power solution to meet your necessary requirements.
To help you with any specific DIN Rail Power Supply requirements or questions Sunpower’s friendly and expert team will be happy to talk to you to discuss your options. Feel free to call us on 0118 9823746 for further information.