Din Rail Power Supplies

Showing 46–51 of 51 results

  • 960W Three Phase DIN RAIL with PFC Function

    The TDR-960 series is a three phase industrial din rail power supply with built-in PFC function. Standard functions include cooling by free air convection, built-in constant current limiting circuit, current sharing up to 3840W (3+1) and protections including short circuit, overload, over voltage and over temperature.

    Features

    • Three-phase AC 340-550V wide range input (Dual phase operation possible)
    • Width only 110mm
    • Built-in active PFC function compliance to EN61000-3-2
    • High efficiency 94.5% and low power dissipation
    • Protections: Short circuit/Overload/Over voltage/Over temperature
    • Cooling by free air convection
    • Built-in constant current limiting circuit
    • Can be installed on DIN rail TS-35/7.5 or 15
    • UL508 (Industrial control equipment) approved
    • EN61000-6-2 (EN50082-2) industrial immunity level
    • Current sharing up to 3840W (3+1)
    • Built-in DC OK relay contact
    • 100% full load burn-in test
    More information Compare
  • 960W Ultra Slim DIN Rail Power Supply

    The SDR-960 is an ultra slim high performance DIN rail power supply with 94% high efficiency, cooling by free air convection and a slim width design (110mm). Standard functions include built-in active PFC function, DC OK relay contact alarm signal output, parallel function (up to 4 units), front panel DC voltage adjustment, front panel LED…

    Features

    • AC Input 180~264VAC
    • 130% peak load capacity
    • Width only 110mm
    • Built-in active PFC function compliance to EN61000-3-2
    • High efficiency 94% and low power dissipation
    • Protections: Short circuit/Overload/Over voltage/Over temperature
    • Cooling by free air convection
    • Built-in constant current limiting circuit
    • Can be installed on DIN rail TS-35-7.5 or 15
    • UL508 (Industrial control equipment) approved
    • EN61000-6-2 (EN50082-2) industrial immunity level
    • Current sharing up to 3840W (3+1)
    • Built in DC OK relay contact
    • 100% full load burn-in test
    More information Compare
  • Din Rail Instal Redundant Module

    20A redundancy (decoupling) module for 24Vdc power system. Containing 2 sets of 20A Or-ing diodes with wonderful heat dissipation deployment, DR-RDN20 gives you a new option for safe connection of 1+1 redundant set-up. Not only perfectly decoupling power sources from each other but also from the load, DR-RDN-20 also provides users monitoring signals for both…

    Features

    • Suitable for redundant operation of 24V system
    • Installed on DIN Rail TS35 / 7.5 or 15
    • Relay contact signal output and LED indicator for input failure alarm
    • Cooling by free air convection
    More information Compare
  • IP TP Media Coupler – KNX IP Router

    The IP TP media coupler (KSR-01IP) connects via an ethernet cable – KNX IP and KNX TP for commissioning, addressing and parameters setting, visualisation and diagnostic operations between devices on the KNX bus.

    Features

    • KNX IP router
    • 4 IP/TP tunnelings
    • No additional external power supply required
    • Universal Plug and Play
    • Telegram filtering
    • Built-in web front-end page
    • Dimension(WxHxD):36x90x71mm
    • 3 years warranty
    More information Compare
  • KNX 8 Channel Universal Actuator

    The KNX 8 channel Universal Actuator is suitable for different load situations and possible for many application areas with up to 8 independent channels

    Features

    • 8 channel actuator in a compact size
    • Suitable for various and mixed applications
    • For AX, C-load, capacitive and inductive of loads
    • Program via ETS5.0 software
    • Manual control via Pushbutton
    • Programmable various time and scene function
    • 3 years warranty

    More information Compare
  • KNX USB Interface

    The KNX USB Interface (KIS-01U) is a USB interface for establishing a bidirectional connection between a PC and the KNX installation bus.

    Features

    • KNX-USB interface
    • No additional external power supply required
    • KNX commissioning, addressing and parameter settings
    • KNX protocol and system visualization
    • Diagnostic operations
    • Long messages up to 220 byte APDU
    • Dimension(WxHxD): 36x90x71mm
    • 3 years warranty
    More information Compare

Sunpower’s DIN rail power supplies range is available in an array of different form factors and power ratings, starting at 10W going up to 960W with output voltages from 5 to 48 volts. All of our DIN rail power supplies are of a fan less design but each individual product has their unique functions and input characteristics, whether it be a wide or high input range, or one, two or three phase operation.

All of our products are installed on DIN rail TS35/7.5 or 15 and the majority of our DIN rail power supply units come with built-in PFC. Other features within our DIN rail power supply units include low no load power consumption, DC OK relay contact and high efficiency. A number of the larger DIN rail power supply units that we stock also have a parallel function so that current sharing can be achieved which allows for installs to be created of up to 3840W with redundancy and UPS modules also available.

Our DIN rail power supplies are designed for use in industrial, automation and process control applications and meet the requirements of UL508, for industrial control equipment and will provide the power solution to meet your necessary requirements.

To help you with any specific DIN Rail Power Supply requirements or questions Sunpower’s friendly and expert team will be happy to talk to you to discuss your options. Feel free to call us on 0118 9823746 for further information.